AUTONET TV

Singing a Different Tune (Up) (Tune Ups)

Posted September 20, 2020 2:05 AM

Engines required a lot more maintenance in earlier times.  You'd have to have your spark plugs, wires, rotors, caps, distributor points, fuel and air filters changed periodically.  There were mechanical adjustments of a vehicle's timing, dwell, spark gap and idle mixture, too. Unless you like to tinker with old cars, a lot of those terms won't mean much to you. 

That service was called a "tune up" back then, and you can see why.  But now, computers have reduced the number of maintenance items, and a tune up is a whole lot different than it used to be.  In fact, in some vehicle service facilities, that term is also a thing of the past. 

A tune up of today would more accurately be called simply periodic maintenance. Now, most vehicles still have spark plugs and wires, fuel filters, air filters and PCV valves, and they should be inspected tested and/or replaced at regular intervals.  Your vehicle's manufacturer has made recommendations on how often that should be. But it depends on your driving habits. Do you regularly tow a trailer? Do you drive on dusty roads often? Are you driving mostly stop and go in the city?  Depending on your answers, to those maintenance intervals might have to be more frequent.

Your service advisor will likely remind you about those "must check" items such as spark plugs and wires, air filter and oxygen sensor.  And now that the old-fashioned tune ups don't require you to take your vehicle in for maintenance as often, you can get the same benefit from scheduled oil changes or tire rotations.  When your vehicle is in for those, a technician can keep an eye on your other systems (fuel, emissions, ignition) to make sure they are operating correctly.

One thing to remember.  When you take your vehicle in for regular service or a specific issue, don't ever hesitate to ask you service advisor to explain what's being done and why.  Hey, "In Sync" may have been a boy band of an earlier era, but it's always good for you and your service advisor to be "in sync" when it comes to what maintenance is good for your vehicle.

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
http://www.houstonwestsideautomotive.com

---

It's Brake Time (Brake Calipers)

Posted September 13, 2020 12:11 PM

Race car drivers have demonstrated the advantages of disc brakes, so most modern vehicles use them.  Sometimes just the front wheels have disc brakes, but many vehicles now have them all the way around. 

A major component of the disc brake is called a caliper.  It works by squeezing brake pads against the disc or rotor, kind of like a bicycle hand brake.  The brake pads themselves are what contact the rotor, causing friction to build and the wheel to slow down, but it's the calipers that apply the pressure to the pads.

Caliper design has evolved over the years, and there are two common types.  One is called a floating caliper.  It has one or two pistons on one side of the disc. When you push down the brake pedal, the piston or pistons in your caliper put pressure on that one side.  A mechanism connected on the other side of the disc applies pressure as well, squeezing your disc so the vehicle stops.  Floating calipers are less expensive since they have fewer parts.

The other type is called a fixed caliper.  They use pistons on both sides of the disc, sometimes several.  They are often used in more high-performance or heavy-duty vehicles.

Calipers can have rubber seals to keep out dirt, debris and moisture, but when that rubber wears out, sometimes the calipers can get contaminated.  They can stick or start leaking; they can even rust.  Then your caliper can get stuck applying that "squeeze" when you are not pressing on the brake pedal.  Or they can get stuck in the other position, not applying stopping power when you press the pedal.

When this happens, it's not unusual to feel your vehicle pull to one side when you brake.  You might notice a burning smell from the constant friction if the caliper is stuck on, plus you may feel the heat from the wheel after you park and get out of your vehicle.  Sometimes you'll hear a high-pitched sound or clunk if your calipers are binding up. 

That's your cue to have them checked out at your vehicle service center.  If your calipers aren't working correctly, it can be a safety hazard.  Sticking calipers can affect your ability to steer and stop; this is the kind of "brake time" you need so you can get them back on track and working properly.

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
http://www.houstonwestsideautomotive.com

---

For 4x4s (Maintenance of 4x4 Vehicles)

Posted August 30, 2020 8:29 AM

Some people love 4x4 vehicles, the true 4-wheel drive works of engineering like Jeeps and 4x4 pickups that allow you to seemingly go anywhere on the planet. You can climb up a 40-degree rock trail with some planning and skill (always careful to protect the environment, of course), or you can get through the deepest snow.

But with that added capability comes additional complexity, drive-train components and other systems that less capable vehicles don't have.  And that is why when it comes to 4x4s, you have to maintain them a little differently from those vehicles that spend their lives on pavement.  Here are some of the key things to keep an eye on:

• Transfer case—This transfers power from the engine to the wheels.  A transfer case has fluid in it that needs to be changed at intervals recommended by the manufacturer.  Your service advisor will let you know how often that is and will keep track of your service dates.  You will need to make sure the transfer case seal is working properly.  Otherwise, transmission fluid could get in and cause damage that is costly to fix.  Some transfer cases have an electric motor that shifts it through gears, and its connections are often exposed to the elements, making them vulnerable to damage and corrosion.  Proper maintenance will keep those connections working like they should
• Front and rear differentials—These also have to have the right amount of fluid and should be checked regularly.  Your service advisor can let you know when you need that fluid changed as the owner's manual recommends.  It's important the service is performed correctly with the proper lubricant so it will work the way it is designed to.
• Brake lines—Those 4x4s practically beg to go into wet spots. They also are great machines to conquer snow: road salt, brine and all.  Moisture, salt and brake lines are a recipe for corrosion, so brake lines need to be inspected regularly.  There are anti-corrosion sprays or white lithium grease that can retard corrosion.  Remember, getting there is half the fun, but not being able to stop is no fun at all.

So enjoy your 4x4 and what it can do that other vehicles can't.  Just remember that even though it's tough on the outside, it needs special care to keep it going.  Oh, and remember to take care of the environment when you go off-roading, too. 

---

Wasteful Thinking

Posted August 9, 2020 8:42 AM

With the weather getting colder, you might be tempted to start your vehicle up, let it idle for 15 or 20 minutes and then get in the nice, cozy cabin.  Some vehicles offer remote starting that let you do that from the comfort of your home or apartment.  But is letting your vehicle idle like that good for it?

Manufacturers say it doesn't harm the vehicle.  They say it's because modern vehicles are made differently from those in the past.  Just about all newer vehicles employ fuel injection which uses computers to adjust the amount of gasoline that goes into the cylinders.  The engine gets only the fuel it needs, taking conditions into account.

Older vehicles, on the other hand, used to use carburetors.  When you started a cold engine, the carburetor wasn't able to adjust the gasoline amount depending on conditions.  Some of the gasoline would mix with oil and the pistons wouldn't get the same lubrication as they would with undiluted oil.

So yes, you can warm up your newer vehicle for your own personal comfort.  But consider how much fuel you are wasting.  That is not only throwing away money, it's a waste of natural resources.  And it puts more carbon into the atmosphere. 

Automakers have to be mindful of what fuel economy their vehicles can achieve.  So the flip side of the remote starts they offer is a "stop-start" feature.  When you stop your vehicle, even at a stoplight, your vehicle will turn the engine off.  When you take your foot off the brake and step on the accelerator, it starts up right away.  That feature can save as much as 10 percent of the fuel your vehicle uses. 

Your vehicle may not have that start-stop feature, but you can still save fuel by shutting off your engine manually if you are waiting somewhere, like a parking lot or perhaps sitting outside your child's school waiting to pick him or her up.  It saves you money and contributes to a healthier atmosphere for our planet.

---

An Oil for All Seasons (Engine Oil Selection)

Posted June 7, 2020 9:47 AM

You swap your winter boots for flip-flops in the summer.  Why not change your winter engine oil for summer, hot-weather oil?  While it may seem like it makes sense, there's some good news.  Most drivers don't have to, and here's why.

Engine oil can be made in different thicknesses.  That thickness is called viscosity, how easily it flows.  Now, it makes sense that the hotter it gets, oil gets a little thinner and doesn't lubricate as well.  So if you used a thicker oil in the summer, it's logical that it would protect better in the hotter weather. 

While there was a time when oils could be only made in one viscosity, times have changed.  Using an ingenious formula, oil can now be created that changes its viscosity (called "multi-viscosity") as the temperature rises and falls.  It self-adjusts to match the conditions.  Now that's what I call a great invention.

In most temperate climates, you don't have to swap out the type of oil you use in your vehicle each season. There are exceptions in extreme climates, but your service advisor can advise you on that.  Your vehicle's owner's manual recommends the proper viscosity oil to use.

Remember that even though you may not have to switch to a different type of oil, you DO have to CHANGE the oil at certain intervals.  That's because oil eventually breaks down and picks up contaminants, and if you have old, dirty oil in your engine, it can cause damaging friction and heat. Regular maintenance at your vehicle service facility will ensure that your vehicle is running like a well-oiled machine. 

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
http://www.houstonwestsideautomotive.com

---

H20 No! (Driving Through Standing Water)

Posted May 10, 2020 10:52 AM

In a year marked by unusually heavy flooding in North America, drivers are very aware of the possibility they may find themselves driving where water has come over the road.  It can be a daunting and frightening situation.  Flooding waters can move quickly and unpredictably, so you have to keep your wits about you when you encounter that situation.

Here a sample of one vehicle manufacturer's guidelines on what to do.  First, the vehicle is designed to go through some water, but you must be careful.  Never attempt to drive through water deeper than the bottom of your tires.

You can get out of your vehicle to check the depth of the water, but you can never be sure that you aren't going to drive into a spot where the road has washed away.  You can't see below the surface of the water, and suddenly you could find yourself in a place where the road drops off unexpectedly.  In swift moving storm runoff, your vehicle could literally be floating away with the current, putting your life and those of your passengers in mortal danger. 

Never go more than 5mph/8 km/hr when you drive through standing water.  That minimizes the waves you create.  If you do find yourself in water that is touching your drivetrain components, that water can damage them.  And if you get water in your engine, it can lock up in seconds and stall.  The potential damage can be catastrophic.

You may have found yourself driving in water deep enough to reach your drivetrain components, and it's essential that you have a technician check the fluids to make sure they haven't been contaminated.  That includes engine oil, transmission and axle.  Driving with fluids contaminated with water can severely damage those components. 

The bottom line is to avoid driving through water at all if you possibly can.  Check your vehicle's owner's manual to see if there are specific guidelines for driving YOUR vehicle in standing water.  It's information that could save your life.

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
http://www.houstonwestsideautomotive.com

---

It Pays to Take Care of Your Transmission at Westside Automotive

Posted May 3, 2020 10:20 AM

If you've been paying attention, you've noticed that vehicle engines are getting more and more powerful in Houston. At the same time, they are getting better and better fuel economy. I've gotta tell 'ya, most of that's because of technological advances in transmissions. To get a better understanding of why that is, let's talk bicycles.

You've probably seen plenty of cyclists on Houston roads. Perhaps you ride yourself. Then you know that a cyclist's cadence is the number of times per minute he or she pedals. The ideal pedal speed is the zone where they can most efficiently generate power over a sustained period of time. The experienced TX cyclist uses her gears to keep her pedal speed in the ideal zone whether she's climbing a hill, cruising on a flat stretch or killing a downhill.

Think of it this way: if you have a 1-speed bike, you really have to pump hard to get up to speed. Your top speed is limited by how fast as you can pedal. And if you're climbing a steep TX hill – forget about it.

Now let's add a couple of gears: one lower and another one higher. With the lower first gear, you can get up to your ideal pedal speed more quickly. When you shift to second, your pedal speed drops below ideal for a while as you work to get back to peak efficiency. Same thing happens when you shift to third, but now you can go much faster than you could with a 1-speed bike using the same effort. Add more gears and you can see that it's much easier to maintain ideal pedal speed. The result, quicker starts, better hill climbing, higher top speed and, most of all, a lot less fatigue for the Houston rider.

Like a cyclist on a bike, every vehicle engine has an ideal engine speed called its power band. When an engine is running in that zone, it can make power very efficiently. It's the vehicle transmission's job to keep the engine in the power band over a wide range of operating conditions. Today 5 or 6 speed automatic transmissions are pretty much the minimum, and 7 and 8 speeds are fairly common in Houston.

Obviously these sophisticated transmissions are very expensive. In fact, next to your vehicle engine, your transmission is the most expensive component in your vehicle, so it pays to take good care of it. Your manufacturer has a recommended service interval for changing your old, contaminated transmission fluid. Servicing your transmission on schedule at Westside Automotive keeps it operating at its best and can prevent costly damage. Ask your friendly and knowledgeable Westside Automotive advisor if it's time for transmission service. Come see why smart Houston drivers trust their transmissions to Westside Automotive.

Give us a call.

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
http://www.houstonwestsideautomotive.com

---

Idle Talk about Engines (Causes of Rough Engine Idling)

Posted March 29, 2020 8:12 AM

When you slow down at stoplight, your vehicle's idle should be smooth as silk.  But what happens when the engine is missing or idling roughly? That's your engine's way of telling you, "Hey, I've got something wrong with me and if you don't get someone to find out what it is, I may not start the next time you turn the key."

You can help your service facility if you can describe the problem in detail.  Here's a list of things to make a note of:

• When is the problem happening, when the engine is cold or when it's been running for a while?
• Does the rough idling occur when I'm accelerating or when I'm going at a steady speed?
• Does it happen at high speeds?  Does it happen low speeds? Does it happen at both?

Make sure you describe the problem in as much detail because it will help a technician diagnose the problem.

One of the first things they'll check is how the spark plugs are firing.  Modern iridium plugs are supposed to last a long, long time.  But they CAN eventually wear out.  Inspecting the firing end can help the technician figure out the root of the problem.  Corroded or worn out spark plug wires, too, can contribute to an idling irregularity. 

There are other potential problem spots, too.  The technician may check the ignition coil, timing piston rings, valves and cylinder walls. 

If the mixture of air and fuel isn't correct, that may affect how smooth your vehicle is running.  Your service facility is equipped with diagnostic equipment that helps them pinpoint the problem.  Once that idle is smoothed out to the way it used to be, you'll be the smoothest operator on the road.

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
http://www.houstonwestsideautomotive.com

---

Westside Automotive Alternator Replacement Service in Houston

Posted January 12, 2020 10:22 AM

 

Your vehicle alternator doesn't get enough credit. Though your battery gets your engine started, after that – it's all about the alternator. 

Driving around Houston is a lot of work for your alternator, and as upgrades such as heated steering wheels, cooled seats, stability control and lane departure warning become more common, it will have to work even harder. Eventually this workhorse just wears out. When it does you have no choice but to order an alternator replacement because your vehicle won't run without one. 

Come see your friendly and professional service advisor at Westside Automotive to learn more.

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
http://www.houstonwestsideautomotive.com

---

Hold the Oil! (Oil Pan Gasket Replacement)

Posted January 5, 2020 7:44 AM

You've likely heard how important oil is to your vehicle's engine. Did you know that there's one part that's responsible for holding that oil so you can use it every day? It's called the oil pan, and it sits at the bottom of the engine.

The oil pan is a vital, though simple, part of your engine's lubrication system. Oil circulates through parts of your engine to keep them lubricated. It reduces friction so everything works smoothly. Without oil, friction would quickly destroy your engine. The oil pan keeps that oil contained in the lubrication system, so it's important that the oil doesn't leak out. Since it's a metal part attached to another metal part, there is a gasket between the oil pan and the part of the engine it attaches to.

Various things can put stress on the oil pan and gasket, including weather extremes, the speed you're traveling and the condition of the oil. You may drive over a couple of bad roads and kick up debris onto your oil pan. All this wear and tear, heat and time can take their toll. So after a while, the gasket can just wear out and start leaking. It usually starts pretty slowly. If you see oil visible under your vehicle where you park it, that might be a sign of a leaky oil pan gasket. Another sign? You smell burning oil coming from your engine. If the leak is bad and your engine has lost a lot of oil, you may eventually see the oil light go on.

Let your service advisor know if you are experiencing any of these things. Driving with insufficient oil can badly damage your engine. And it can do it quickly. A Westside Automotive trained technician will check to find the source of the leak. It may just be a gasket, but it also could be the oil pan is damaged and needs replacing as well.

This is a repair you should get taken care of. Your engine needs its lubrication system intact to provide you many years of service.

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
http://www.houstonwestsideautomotive.com

---