AUTONET TV

A "Mounting" Problem (Motor Mounts)

You know how heavy your engine and transmission are, so you can imagine how tough the parts that hold them onto your vehicle's sub-frame must be.  Not only must they support the weight, they also have to isolate vibrations and noise from the passenger cabin.  Pretty tall order, wouldn't you say?

The parts that face that task daily are called the motor mounts, or engine mounts.  They are usually made of rubber with steel brackets.  Others contain a liquid for vibration and sound isolation. 

Most vehicles have three or four motor mounts, and while rubber or hydraulic liquids do a good job of damping the vibrations from the engine, they also have their limitations.  The problem with rubber is that it gets old and brittle.  Plus, if there's an oil leak anywhere in your engine and oil gets on the rubber motor mounts, rubber will deteriorate even more quickly.  As for the liquid motor mounts, they can develop leaks and stop working. 

Here are signs a motor mount is going bad.  You may hear a loud clunking or banging sound under the hood.  That means the weight of the engine is shifting around enough to bang against other metal parts.  You may feel bad vibrations, and the engine may feel like it's moving around in a strange way.

When things get to that point, your vehicle can be damaged from that heavy engine knocking against things, and its time to replace one or more motor mounts.  Schedule a visit to your vehicle service facility. There, a technician will assess your motor mounts; if one bad one is found, it's not unusual that others are likely to fail soon and should be replaced before they do.

Because all vehicles are configured differently, some motor mounts are easily replaced.  But others can be much trickier, take a lot longer and therefore are more expensive to replace. 

It's important for your engine's health to make sure motor mounts are sound and solid.  You will maintain that quiet, vibration-free ride and could save your engine and transmission from major wear and tear.

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
www.houstonwestsideautomotive.com

Command Performance (Engine Air Filter)

The internal combustion engine in your vehicle counts on two things that mix together to be burned in the engine for power: fuel and air.  Both are important, of course.  If you run out of fuel, your engine won’t run at all.  Since there’s plenty of air around, you won’t run out of air, but you could feel your vehicle’s performance suffer if the engine air filter starts to get clogged. 

It's important that the air that enters your engine be free of dirt, dust, and debris to prevent damage to internal components.  That’s where the engine air filter comes in.  It prevents those particles from entering the engine, an important job that most people just take for granted.

After a while, your air filter will get dirty, which results in less air reaching the engine.  Modern fuel injected engines can adjust the amount of gas to mix with the air that is getting in, so your fuel economy won’t change significantly.  What will change is how well the engine performs, its acceleration.  In one test, a US Department of Energy study showed that a dirty air filter reduced a vehicle’s get-up-and-go by as much as 11 percent.  

The company that made your vehicle includes guidelines in your owner’s manual on how frequently that filter should be changed, and doing so will maintain your engine’s performance. If you drive in dusty, dirty areas or those with a lot of industrial pollution, we recommend you replace the engine air filter more frequently than the manufacturer’s recommendations.  

When you bring your vehicle to us for regular maintenance, we will routinely check several components, including your engine air filter, and recommend a change when we see signs it’s needed. It’s good for your engine, and you’ll enjoy the performance you expect.

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
www.houstonwestsideautomotive.com

Taking the Heat (Heater Hose Maintenance/Repair)

If you have an internal combustion vehicle, you know it has a lot of hoses that carry various fluids.  And if you have a heater in your vehicle, you'll have heater hoses.

A heater hose connects to and from the engine so some coolant can be circulated through a little radiator called a heater core.  In cold weather, that heater core acts as a heat exchanger to heat up your cabin.

Even in the hot weather, the heater hoses can prove problematic.  That's because they may remain pressurized even though you're not running your heater.  Heater hoses are made out of tough materials since they must handle heat and pressure.  But even the durable rubber, plastic and metal they are made out of can crack or leak from years of use.  That means coolant can be sprayed out into the engine compartment or leak onto a driveway or garage floor. 

You may be able to see a puddle of coolant under your vehicle or perhaps smell the odor of the coolant under the hood.  Some say it has a sweet smell.  Another sign coolant may be leaking out of the heater hoses is your engine may be running hotter.   You'll be able to tell by watching the heat gauge on your dash.  Let's say your heat gauge usually points just slightly below halfway between the C and H (Cold and Hot) of the heat gauge.  But now it is just slightly above.  That's enough to tell you that the coolant temperature has gone up a little, a possible sign of trouble.

This is a good time to swing by your service facility and have them take a look. If they catch the leak when it's small, it's a relatively simple matter of draining the coolant, replacing the hoses and replacing the coolant.  Sometimes, though, a heater hose can suddenly burst and a lot of coolant can leak out quickly.  That can, in turn, cause your engine to start to overheat.  In that case, you may see your vehicle's temperature gauge shoot up pretty quickly.  Then it's best to pull over and have your car towed to a repair facility since driving with no coolant can cause severe engine damage.

Preventative maintenance is your best insurance against heater hose problems.  A technician will periodically check for any signs of cracks or leaks.  You should expect to replace a heater hose at least once during the time you own your vehicle.

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
www.houstonwestsideautomotive.com

Clean Machine (Fuel and Air Induction Cleaning)

As your vehicle ages, its performance isn’t quite what it used to be, but many of us never notice the change because it’s gradual.  So here are a few questions to ask yourself.  Does your vehicle feel like it doesn’t have the pep that it used to? Have you noticed your fuel economy isn’t quite as good as it once was? Does it idle roughly or is it hard to start?  Do you hear the engine knocking? Has it recently failed an emissions test?

All of those can be signs that your fuel and air induction systems are dirty and need cleaning.  Your fuel system takes gasoline from the tank to the engine’s combustion chambers where fuel injectors spray fuel that mixes with air and is ignited by spark plugs.  Black carbon deposits eventually can build up, obstructing fuel flow and diminishing your engine’s performance and fuel efficiency.

The air induction system is what allows air to go into the engine’s combustion chamber.  Getting the proper air flow is necessary for you to quickly start your vehicle, accelerate, and perform the way it should and idle smoothly when you’re standing still.  Like the fuel system, your air induction system can get blocked up with deposits and other contaminants.

A professional fuel and air induction cleaning can help restore your performance and fuel economy, especially when you are experiencing problems.  A technician will use specialized chemicals that can remove the carbon buildup.  In extreme cases, they will remove the fuel injectors and clean them with specialized tools.  

After cleaning, you may notice how much more pep your vehicle has and how smoothly it runs.  Keep your fuel and air induction systems clean and enjoy your vehicle’s performance improvements.

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
www.houstonwestsideautomotive.com

See the Light (Bulb Replacement)

When you notice one of your headlights has gone out, it’s important for the safe operation of your vehicle to get it changed and working again.  Not only is replacing a headlight important for your ability to see in the dark, but it’s also vital that it be lighting your way and aimed correctly so oncoming drivers aren’t blinded.  

Changing a headlight used to be something a driver might try to do themselves.  But that was back when headlights were standard sizes and fairly easy to access on your vehicle.  That has all changed with new technology and designs in today’s vehicles.  Most lamps are now LEDs, and there are different sizes, intensities, and shapes in different vehicles. Accessing those bulbs has also grown extremely difficult in some cases, and we recommend you have one of our professional technicians do it for you.

It's just as important that your brake lights and side marker lights work, too, as they contribute to the safe operation and visibility of your vehicle.  A technician will check to see what is causing a light not to illuminate, which could be a bulb, but also could be a problem with the electrical system in that bulb’s circuit.

Having all your lights working is not only a matter of convenience, but a matter of safety too.  So don’t be in the dark when you don’t have to be. Let our technicians light up your life a little by making sure all your bulbs are working right.

Westside Automotive
12510 Oxford Park Dr.
Houston, TX 77082
281-589-8984
www.houstonwestsideautomotive.com